RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: ausfester
Showing results 1 to 16 of 16
Search took 0.03 seconds.
Forum: RC Jets
07-29-2014, 05:38 AM
Replies: 2,625
Views: 738,345
Posted By ausfester

I noticed my Excalibur trim changed at full...

I noticed my Excalibur trim changed at full noise.
Flying inverted, knife edge and with full flap was also difficult so I put a few washers under my custom made engine mounts, (which I suspect made...
Forum: RC Jets
06-23-2014, 02:22 AM
Replies: 2,625
Views: 738,345
Posted By ausfester

I'll second Tony from Trim Air in Aus. Bullet...

I'll second Tony from Trim Air in Aus. Bullet proof electric retracts, what more can I say
Forum: RC Jets
06-02-2014, 02:45 AM
Replies: 2,625
Views: 738,345
Posted By ausfester

Guys, the k80 and k100 are the same can size. I...

Guys, the k80 and k100 are the same can size. I fit my 80 with a little fiddling and flexing the fuze without cracking anything. I would suggest using some thicker ply to make the turbine sit higher...
Forum: RC Jets
05-07-2014, 11:14 PM
Replies: 2,625
Views: 738,345
Posted By ausfester

Watch the sales of these things go through the...

Watch the sales of these things go through the roof with the BS boomerang is producing at the moment.
Forum: RC Jets
05-06-2014, 02:31 AM
Replies: 2,625
Views: 738,345
Posted By ausfester

geeze they'll go quick, you guys better get in...

geeze they'll go quick, you guys better get in fast
Forum: RC Jets
04-30-2014, 03:08 PM
Replies: 2,625
Views: 738,345
Posted By ausfester

My build was pretty great to be honest, mounting...

My build was pretty great to be honest, mounting turbine a tad tight, my hitec servos we're a perfect reach for alerons without extension.
Same old little extra glue in some real easy places to...
Forum: RC Jets
04-25-2014, 03:40 AM
Replies: 2,625
Views: 738,345
Posted By ausfester

Had a great maiden today, running K80G and Trim...

Had a great maiden today, running K80G and Trim Air Electric Retracts with Hitec 5645mg Servos all around.
Predictable and smooth with only a few clicks of elevator trim.

Landing was just perfect...
Forum: RC Jets
04-17-2014, 03:43 PM
Replies: 2,625
Views: 738,345
Posted By ausfester

Well guys, mines finished. Balanced with an...

Well guys, mines finished. Balanced with an additional 330 grams of lead in the Nose.
Had 3 Life batteries in the front nose, and bubble trap as physically far forward as humanly possible. Was...
Forum: RC Jets
04-15-2014, 02:57 PM
Replies: 2,625
Views: 738,345
Posted By ausfester

Brain fade here, do we balance CG with retracts...

Brain fade here, do we balance CG with retracts up or down?
I'm learning towards up.....
Forum: RC Jets
04-12-2014, 03:57 AM
Replies: 2,625
Views: 738,345
Posted By ausfester

All three jets I've built I've always measured CG...

All three jets I've built I've always measured CG with bubble trap full.
Theory behind that is it should never be empty...if it is your likely going to have a serious problem. Also it would be...
Forum: RC Jets
04-09-2014, 04:23 AM
Replies: 2,625
Views: 738,345
Posted By ausfester

Hey guys just confirming that everyone agrees...

Hey guys just confirming that everyone agrees 170mm is the correct CG?
Forum: RC Jets
04-05-2014, 04:01 AM
Replies: 2,625
Views: 738,345
Posted By ausfester

Some interesting findings today with my build....

Some interesting findings today with my build. The manual says mini servos for the rudders. One boom the mini servo kinda just fitted, there was almost not enough wood to screw them in straight down...
Forum: RC Jets
04-04-2014, 12:02 PM
Replies: 2,625
Views: 738,345
Posted By ausfester

Did you guys make sure the wing clamps were...

Did you guys make sure the wing clamps were loose?
I assembled mine no problems not even much force, just a spray of silicone lubricant on the carbon tube and bam! This was from the Aussie batch tho
Forum: RC Jets
04-03-2014, 12:22 PM
Replies: 2,625
Views: 738,345
Posted By ausfester

might see if I have something stronger for the...

might see if I have something stronger for the elevator lying around and leave the rest stock. Thanks Dave and Ken
Forum: RC Jets
04-03-2014, 02:50 AM
Replies: 2,625
Views: 738,345
Posted By ausfester

Ken hooked me up with the sports version of this...

Ken hooked me up with the sports version of this model, looks like a pretty quick build. Got it all hinged up in just a few hours.

Is anyone actually using the horns supplied with the kit?
Forum: RC Jets
03-26-2014, 12:23 PM
Replies: 2,625
Views: 738,345
Posted By ausfester

Did you guys reinforce or re-glue any of the...

Did you guys reinforce or re-glue any of the retract mounts?
Showing results 1 to 16 of 16


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.