RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: kryptonite
Showing results 1 to 11 of 11
Search took 0.11 seconds.
Forum: Glow Engines
09-25-2007, 10:12 AM
Replies: 54,816
Views: 5,393,570
Posted By kryptonite

RE: Welcome to Club SAITO !

There were a couple of comments a few msgs back about the Saito 125 and props.

I've experimented with a number just last week and keep coming back to the APC 16x6. I'm getting 9100 rpm on 15%...
Forum: Glow Engines
09-06-2007, 03:39 PM
Replies: 54,816
Views: 5,393,570
Posted By kryptonite

RE: Welcome to Club SAITO !

Skillet, I doubt its the fuel. You don't seem to have a problem starting it - bad fuel usually is hard to start.

Almost always, when an engine dies when it is going from mid to full throttle -...
Forum: Glow Engines
09-05-2007, 10:29 PM
Replies: 54,816
Views: 5,393,570
Posted By kryptonite

RE: Welcome to Club SAITO !

Did you test both engines using the same fuel tank setup. I suspect the plumbing - either air leaks in the main line, the muffler pressure line or the tank is placed too low relative to the carb...
Forum: Glow Engines
09-04-2007, 01:03 PM
Replies: 54,816
Views: 5,393,570
Posted By kryptonite

RE: Welcome to Club SAITO !

Thanks for the info. I think the little play is then normal. No, there is no movement on the prop driver.
Now as far as the gritty feel - I'm hesistant to say there is none - it does not feel...
Forum: Glow Engines
09-04-2007, 09:50 AM
Replies: 54,816
Views: 5,393,570
Posted By kryptonite

RE: Welcome to Club SAITO !

I had a great weekend at the field with my 1.25 Saito powered Twist 60 - what a joy to fly with an engine with such an incredible throttle response. When I got home, I primed and lubed the engine...
Forum: Glow Engines
08-31-2007, 10:13 AM
Replies: 54,816
Views: 5,393,570
Posted By kryptonite

RE: Welcome to Club SAITO !

My Saito 125 suddenly became a lot more powerful after I had about 2 gallons through it. Its almost like a magical transformation. Its now turning an APC 16x6 at 9200 rpm with the HS needle about 2...
Forum: Glow Engines
08-30-2007, 08:47 AM
Replies: 54,816
Views: 5,393,570
Posted By kryptonite

RE: Welcome to Club SAITO !

Thanks - good to know that I'm not alone. No leaks when wet - and the power is awesome. Starts also on the first flick - so I won't worry about it.
I'm using CoolPower MV for 4 strokes. I think...
Forum: Glow Engines
08-29-2007, 12:59 PM
Replies: 54,816
Views: 5,393,570
Posted By kryptonite

RE: Welcome to Club SAITO !

A couple of months ago - I was concerned that my then new Saito 125 was not developing enough power. It had only a gallon through it then. Now, after one more gallon - I was stunned that I'm getting...
Forum: Glow Engines
05-08-2007, 08:39 PM
Replies: 54,816
Views: 5,393,570
Posted By kryptonite

RE: Welcome to Club SAITO !

Thanks for the tip - I usually do not trust my own ears when tuning - although I admit I wasn't paying too much attention to change in the amount of smoke and spray while actually tweaking the HS...
Forum: Glow Engines
05-08-2007, 08:31 PM
Replies: 54,816
Views: 5,393,570
Posted By kryptonite

RE: Welcome to Club SAITO !

Actually the 16-6 is the recommended prop for the Saito 125, for maximum thrust. It should turn it to 8500 rpm range, according to tests by Fly RC magazine and other reviewers - although, Mike...
Forum: Glow Engines
05-08-2007, 03:32 PM
Replies: 54,816
Views: 5,393,570
Posted By kryptonite

RE: Welcome to Club SAITO !

After flying electric parkies for this past two years - I've decided to make a glow bird ( to make sure I won't regret my decision I went and got myself a Saito 125a GK[8D] ). The engine was bench...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.