RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: rajul
Showing results 1 to 25 of 184
Search took 0.10 seconds.
Forum: Glow Engines
11-20-2021, 07:31 PM
Replies: 54,701
Views: 5,314,077
Posted By rajul

There is a very nice instructional video here on...

There is a very nice instructional video here on how to set the timing using a philips head screwdriver https://www.youtube.com/watch?v=bTjExGAoge8
Forum: Glow Engines
11-16-2021, 08:59 AM
Replies: 54,701
Views: 5,314,077
Posted By rajul

How do you ensure that the crank is exactly at...

How do you ensure that the crank is exactly at TDC? It would be nice if some video instruction on setting the engine timing is available.
Forum: Glow Engines
11-16-2021, 05:58 AM
Replies: 54,701
Views: 5,314,077
Posted By rajul

Just curious, how do you use this timing tool?

Just curious, how do you use this timing tool?
Forum: Glow Engines
11-14-2021, 06:56 PM
Replies: 54,701
Views: 5,314,077
Posted By rajul

The color of the viton o-ring is different. I...

The color of the viton o-ring is different. I will check this out when I order a new replacement set.
Forum: Glow Engines
11-14-2021, 05:31 AM
Replies: 54,701
Views: 5,314,077
Posted By rajul

Hi guys, I have replaced all the o-rings in my...

Hi guys, I have replaced all the o-rings in my Saito 125. The intake manifold o-ring at the head was in real bad shape, but since I took down the engine from the plane, I decided to change all the...
Forum: Glow Engines
10-18-2021, 03:22 PM
Replies: 54,701
Views: 5,314,077
Posted By rajul

Hi glowgeek, Dave, thanks a lot for your inputs!...

Hi glowgeek, Dave, thanks a lot for your inputs! Really appreciate it. I will replumb the fuel tank, and give it a go. Any tell-tale signs, especially at the high and low ends, if the o-rings are not...
Forum: Glow Engines
10-18-2021, 08:37 AM
Replies: 54,701
Views: 5,314,077
Posted By rajul

Hi guys, I have a Saito 125 which have been in...

Hi guys, I have a Saito 125 which have been in storage for several years. I made sure I oil it every now and then. No sign of bearing corrosion, valve gaps still good. I would like to know which are...
Forum: Glow Engines
09-25-2021, 03:59 AM
Replies: 54,701
Views: 5,314,077
Posted By rajul

Btw, I found this in the late Bill Robison's...

Btw, I found this in the late Bill Robison's notes:

"A couple you mention though - the white ring is Teflon, it is used to seal the choke plate when one is fitted, it goes in the groove on the...
Forum: Glow Engines
09-25-2021, 03:22 AM
Replies: 54,701
Views: 5,314,077
Posted By rajul

That's what my gut feeling is telling me too....

That's what my gut feeling is telling me too. Besides my Saito 82 and 125 don't use chokes. I guess the chokes are on older 150s?
Forum: Glow Engines
09-25-2021, 02:21 AM
Replies: 54,701
Views: 5,314,077
Posted By rajul

https://cimg8.ibsrv.net/gimg/www.rcuniverse.com-vb...

https://cimg8.ibsrv.net/gimg/www.rcuniverse.com-vbulletin/640x480/img_5191_759751226cc22383a962810d6b52ed4baf624798.jpg
Here's a photo with some scale information. They're either for the Saito...
Forum: Glow Engines
09-24-2021, 09:26 PM
Replies: 54,701
Views: 5,314,077
Posted By rajul

I have to service my Saito 82 and 125 after many...

I have to service my Saito 82 and 125 after many years of storage. I was digging through my inventory of spare parts and found these whitish washers. Not sure if they belong to Saito or OS. Can...
Forum: Glow Engines
02-19-2013, 05:45 AM
Replies: 54,701
Views: 5,314,077
Posted By rajul

RE: Welcome to Club SAITO !

I received my new gaskets for the Saito 125 and 82. There are some viton o-rings which are packed separately. Where would these viton 0-rings be used? I would imagine at higher temperature locations...
Forum: Glow Engines
01-23-2013, 09:30 AM
Replies: 54,701
Views: 5,314,077
Posted By rajul

RE: Welcome to Club SAITO !

Hobbsy, thanks for the info. The other option I have is to make my own gasket. I could use the ultra copper RTV, but I would prefer to cut out my own gasket. What material can I use, and how thick?...
Forum: Glow Engines
01-23-2013, 07:51 AM
Replies: 54,701
Views: 5,314,077
Posted By rajul

RE: Welcome to Club SAITO !

Hello folks, it's been some time since I last posted in this thread. Wow! 950 pages already and still going strong!

Anyway, I just wanted to ask a quick question: I have a Saito 82 (old case)...
Forum: Glow Engines
06-01-2009, 11:21 AM
Replies: 54,701
Views: 5,314,077
Posted By rajul

RE: Welcome to Club SAITO !

I had the joint soldered and the heat shrink tubing I used was a little soft. It broke right at the edge of the solder joint. I'll try your suggestion of just crimping it, and use a harder tubing.
Forum: Glow Engines
06-01-2009, 10:53 AM
Replies: 54,701
Views: 5,314,077
Posted By rajul

RE: Welcome to Club SAITO !

Hi Jim, I had the ground cable connected to one of the rear crankcase bolts. I had the cable and the lug brought forward for the photo.
Forum: Glow Engines
06-01-2009, 09:55 AM
Replies: 54,701
Views: 5,314,077
Posted By rajul

RE: Welcome to Club SAITO !

Hi once again folks! Anyone knows what type of cable works best forgroundingan engine (for a glow plug connector). The cable I'm using seems to break by fatigue after 25-30 flights. Anyone tried...
Forum: Glow Engines
01-16-2009, 12:07 AM
Replies: 54,701
Views: 5,314,077
Posted By rajul

RE: Welcome to Club SAITO !

Well, I managed to make a couple of grip washers with 180 wet & dry, using medium ca as bonding agent. Looks pretty good. Time to test them
Forum: Glow Engines
01-15-2009, 07:53 PM
Replies: 54,701
Views: 5,314,077
Posted By rajul

RE: Welcome to Club SAITO !

Excellent! What grit size did you use?
Forum: Glow Engines
01-15-2009, 11:17 AM
Replies: 54,701
Views: 5,314,077
Posted By rajul

RE: Welcome to Club SAITO !

It's been some time since I last visited club saito. Good to be back here again.

Anyway, I need to make a grip washer that goes between the thrust washer and spinner backplate of my Saito 125...
Forum: Glow Engines
12-24-2007, 07:40 PM
Replies: 54,701
Views: 5,314,077
Posted By rajul

RE: Welcome to Club SAITO !

I received some info from Horizon saying that the SAI125A01A has improved casting around the exhaust ports in
the cylinder head, which strengthens the area.
Forum: Glow Engines
12-21-2007, 11:55 PM
Replies: 54,701
Views: 5,314,077
Posted By rajul

RE: Welcome to Club SAITO !

Is there a difference between the SAI125A01 and SAI125A01A cylinders? Thanks guys http://www.horizonhobby.com/Products/RelatedParts.aspx?ProdID=SAIE125A&Category=Parts%20Listing
Forum: Glow Engines
11-19-2007, 08:21 PM
Replies: 54,701
Views: 5,314,077
Posted By rajul

RE: Welcome to Club SAITO !

I was finding difficulty in searching for the cover as they were listed as "cvr".
Forum: Glow Engines
11-19-2007, 08:14 PM
Replies: 54,701
Views: 5,314,077
Posted By rajul

Forum: Glow Engines
11-19-2007, 08:09 PM
Replies: 54,701
Views: 5,314,077
Posted By rajul

RE: Welcome to Club SAITO !

Can anyone give me the part number for the rocker arm covers for the Saito 125? Thx
Showing results 1 to 25 of 184
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.