RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 4
1
2
3
Last »
Search: Posts Made By: NM2K
Showing results 1 to 25 of 87
Search took 0.12 seconds.
Forum: Glow Engines
03-18-2012, 04:15 AM
Replies: 2,331
Views: 323,397
Posted By NM2K

RE: *** CLUB SUPER TIGRE ***

That looks the same as the muffler that fits my ST G20/15. Sure wish I could buy a couple of those somewhere.


Ed Cregger
Forum: Glow Engines
03-16-2012, 07:23 AM
Replies: 2,331
Views: 323,397
Posted By NM2K

RE: *** CLUB SUPER TIGRE ***

The amount of compression also influences the length of the pipe setup, in addition to the fuel, glow plug and propeller. Lowering the compression is customary when running a tuned pipe. Your glow...
Forum: Glow Engines
05-29-2011, 09:21 PM
Replies: 2,331
Views: 323,397
Posted By NM2K

RE: *** CLUB SUPER TIGRE ***

Super Tigre engines represent a fantastic value for modellers with the patience to learn how to break them in and adjust them properly.


Ed Cregger
Forum: Glow Engines
05-05-2010, 12:10 AM
Replies: 2,331
Views: 323,397
Posted By NM2K

RE: *** CLUB SUPER TIGRE ***

May I suggest a different tactic? How about using a Perry VP-20 or 30 fuel pump? Personally, I prefer the VP-20 if the fuel tank is immediately behind the firewall. No muss, no fuss and not very...
Forum: Glow Engines
01-02-2010, 09:13 AM
Replies: 2,331
Views: 323,397
Posted By NM2K

RE: *** CLUB SUPER TIGRE ***

The 11x8 is my favorite break-in prop for the G90, but a 12 or 13 x 7 or 8 is just fine too. The latter group are fine for flying too. You want to stay away from a 14x6 unless your scale model is...
Forum: Glow Engines
12-29-2009, 01:54 AM
Replies: 2,331
Views: 323,397
Posted By NM2K

RE: *** CLUB SUPER TIGRE ***

After following the manufacturer's instructions for break-in, use the setting technique below to set your model's needles.

Set your needle valves with only an of fuel in the fuel tank. Hold the...
Forum: Glow Engines
12-02-2009, 03:42 AM
Replies: 2,331
Views: 323,397
Posted By NM2K

RE: *** CLUB SUPER TIGRE ***

Yes, IIRC, all Super Tigre engines utilize the same needle valve.

There is/was a third party manufacturer selling needle valves for Super Tigre engines. Ernst? I can't remember, but there should...
Forum: Glow Engines
05-13-2009, 06:24 PM
Replies: 2,331
Views: 323,397
Posted By NM2K

RE: *** CLUB SUPER TIGRE ***

You have an excellent idea in using the mousse can pipe type of muffler. You get a generous rpm increase (compared to stock muffler) while reducing the sound output, plus it can be assembled...
Forum: Glow Engines
05-13-2009, 09:40 AM
Replies: 2,331
Views: 323,397
Posted By NM2K

RE: *** CLUB SUPER TIGRE ***

Encourage your ST G45 to rev way up. It is an ABC engine, after all.

A 10x6 prop is more in line with producing maximum horsepower. Horsepower and quiet are not compatible in most two-stroke...
Forum: Glow Engines
05-10-2009, 03:23 AM
Replies: 2,331
Views: 323,397
Posted By NM2K

RE: *** CLUB SUPER TIGRE ***

.
Forum: Glow Engines
04-21-2009, 02:48 PM
Replies: 2,331
Views: 323,397
Posted By NM2K

RE: *** CLUB SUPER TIGRE ***

Just an addendum to my own previous post, which the messed up editing function in RCU's program appears to have devoured.

I would love to see the Robart fuel pump (in both glow and petrol...
Forum: Glow Engines
03-07-2009, 03:54 PM
Replies: 2,331
Views: 323,397
Posted By NM2K

RE: *** CLUB SUPER TIGRE ***

Because (one possibility) some folks can't seem to give up the muffler pressure line, which disables the regulating function in the Perry Pump. Or something like that.

I used to like the Robart...
Forum: Glow Engines
03-06-2009, 11:45 AM
Replies: 2,331
Views: 323,397
Posted By NM2K

RE: *** CLUB SUPER TIGRE ***

This is a different G20, not the Zenoah. This is one by Super Tigre and it's a little .15 sized glow engine. Thanks for the offer of assistance, though.


Ed Cregger
Forum: Glow Engines
03-06-2009, 02:34 AM
Replies: 2,331
Views: 323,397
Posted By NM2K

RE: *** CLUB SUPER TIGRE ***

I am an ST G20/15 fan and have collected a few. None came with mufflers. In order to fly with a stock muffler, I have gone so far as to buy G20/23 engines just for their mufflers and then resold the...
Forum: Glow Engines
12-29-2008, 06:58 AM
Replies: 2,331
Views: 323,397
Posted By NM2K

RE: *** CLUB SUPER TIGRE ***

The old Super Tigre carbs were designed different and they were a snap to set. The only time a modeler messed with rotating the spray bar was when trying to smooth out the transition from off the...
Forum: Glow Engines
12-02-2008, 04:21 PM
Replies: 2,331
Views: 323,397
Posted By NM2K

RE: *** CLUB SUPER TIGRE ***

The engine with the dished cylinder head is a "K" series. I had the .40 version. Mine was ringed. It was a great running engine, was very reliable and it idled and transitioned beautifully. Mine had...
Forum: Glow Engines
11-29-2008, 09:22 AM
Replies: 2,331
Views: 323,397
Posted By NM2K

RE: *** CLUB SUPER TIGRE ***

If you notice the picture in your posting, Rainedave, you can see that the muffler is still the flow thru muffler, but with an insert.


Ed Cregger
Forum: Glow Engines
11-28-2008, 08:37 PM
Replies: 2,331
Views: 323,397
Posted By NM2K

RE: *** CLUB SUPER TIGRE ***

I had one of the older G21/46 engines that had the rotating baffle plate. I bought it to copy Jim Kirkland's install on the Mustang-X.

While it was a reliable engine, mine never quite matched my...
Forum: Glow Engines
11-28-2008, 04:53 PM
Replies: 2,331
Views: 323,397
Posted By NM2K

RE: *** CLUB SUPER TIGRE ***

I would try running the engine as is at the field. See if someone complains. You might not have to do a thing. Remember, you can't judge how loud your model is if you are running it over your...
Forum: Glow Engines
11-28-2008, 03:20 PM
Replies: 2,331
Views: 323,397
Posted By NM2K

RE: *** CLUB SUPER TIGRE ***

The good part is that there are probably tons of NIB or near NIB large Super Tigres floating around in various places.

I used to groan whenever I saw a relative newbie break out a model with one...
Forum: Glow Engines
11-26-2008, 12:19 AM
Replies: 2,331
Views: 323,397
Posted By NM2K

RE: *** CLUB SUPER TIGRE ***

The first time I answered your question it was for a Zenoah G23. Then I saw that wasn't what you asked for and wrote the second reply, which you have read.

Okay, now for the G20/23 .23 CID glow...
Forum: Glow Engines
11-25-2008, 06:45 AM
Replies: 2,331
Views: 323,397
Posted By NM2K

RE: *** CLUB SUPER TIGRE ***

-


For general sport flying a 16x8 to a 18x8.

I broke-in my G2300 running an 18x8 with the stock muffler, stock glow plug and 5% S&W fuel with 50/50 synth/castor mix. At that time, the...
Forum: Glow Engines
10-31-2008, 01:55 PM
Replies: 2,331
Views: 323,397
Posted By NM2K

RE: *** CLUB SUPER TIGRE ***

-


It depends upon the mood I am in and where the engine has the most convenient amount of "beef".

If the backplate screw hole/boss isn't vented into the crankcase, or easily made to do...
Forum: Glow Engines
10-31-2008, 01:37 AM
Replies: 2,331
Views: 323,397
Posted By NM2K

RE: *** CLUB SUPER TIGRE ***

-


What do you have to trade that is worth about $60? A NIB Fox .45 perhaps? I'll send you a NIB (from Tower directly) ST GS-40, if you are so inclined.


Ed Cregger
Forum: Glow Engines
10-26-2008, 06:45 AM
Replies: 2,331
Views: 323,397
Posted By NM2K

RE: *** CLUB SUPER TIGRE ***

ST engines are of an older design. They were designed with different uses in mind than 3D flying.

What this means is that while the carb works fine for ordinary flying of a decade or two ago...
Showing results 1 to 25 of 87
 
Page 1 of 4
1
2
3
Last »


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.