RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Search
Today's Posts
Mark Forums Read
Vendor Directory
Notices
Search: Posts Made By: rocketman-RCU
Showing results 1 to 11 of 11
Search took 0.11 seconds.
Forum: Glow Engines
11-16-2010, 08:55 AM
Replies: 54,810
Views: 5,381,591
Posted By rocketman-RCU

RE: Welcome to Club SAITO !

My problem is I can't get to the low speed needle without pulling the engine about an inch off the firewall. So, I can't do it while it's running. That's one thing.
Forum: Glow Engines
11-15-2010, 11:01 PM
Replies: 54,810
Views: 5,381,591
Posted By rocketman-RCU

RE: Welcome to Club SAITO !

Everything is new. New carb, all new gaskets, all new o-Rings on the intakes and on the carb insert. New crank, new cams. Still has original valves and springs, but they looked ok. Even tried aux....
Forum: Glow Engines
11-15-2010, 06:49 PM
Replies: 54,810
Views: 5,381,591
Posted By rocketman-RCU

RE: Welcome to Club SAITO !

OK BTW, I'm back to square one with the 1.70R. Turn low speed needle back to manuals recommended 3 turns out. I prime it, it burns out the primer and quits. I guess I will keep opening the low speed...
Forum: Glow Engines
11-10-2010, 12:53 PM
Replies: 54,810
Views: 5,381,591
Posted By rocketman-RCU

RE: Welcome to Club SAITO !

Yes, I have onboard glow on all 3 cylinders and mostly OS F plugs.
Forum: Glow Engines
11-09-2010, 11:59 PM
Replies: 54,810
Views: 5,381,591
Posted By rocketman-RCU

RE: Welcome to Club SAITO !

Currently running 20% Heli fuel, same as always.
Forum: Glow Engines
11-09-2010, 11:46 PM
Replies: 54,810
Views: 5,381,591
Posted By rocketman-RCU

RE: Welcome to Club SAITO !

Rebuilt my Saito 1.70R. Still drops cylinders on transition. Ran low speed needle 6 turns out for 2 years, but now am changing to the recommended 3 turns to see if that helps. Also changed the...
Forum: Glow Engines
11-05-2010, 11:07 PM
Replies: 54,810
Views: 5,381,591
Posted By rocketman-RCU

RE: Welcome to Club SAITO !

A full size Cub is a little different in that you use a lot of forward stick with full power to get the tail up, and then you neutralize the stick until takeoff speed, then up elevator.
Forum: Glow Engines
11-02-2010, 09:41 PM
Replies: 54,810
Views: 5,381,591
Posted By rocketman-RCU

RE: Welcome to Club SAITO !

No, I want an explanation!
Forum: Glow Engines
11-02-2010, 09:39 PM
Replies: 54,810
Views: 5,381,591
Posted By rocketman-RCU

RE: Welcome to Club SAITO !

It looks to me like it should be BDC because the cam lobes are on the same side as the gear dot.?
Forum: Glow Engines
11-02-2010, 05:57 PM
Replies: 54,810
Views: 5,381,591
Posted By rocketman-RCU

RE: Welcome to Club SAITO !

Ok, I forgot the install of the cam gear on the Saito 1.70R. Does the dot on the cam gear go on the crank shaft gear at bottom dead center?
Forum: Glow Engines
07-13-2009, 07:37 AM
Replies: 54,810
Views: 5,381,591
Posted By rocketman-RCU

RE: Welcome to Club SAITO !

All my Saitos run better on synthetic fuel. Especially 20% Heli fuel. 100T, 180, 170R, 450R
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.