RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Springbok Flyer
Showing results 1 to 11 of 11
Search took 0.09 seconds.
Forum: RC Jets
07-16-2018, 02:57 AM
Replies: 1,970
Views: 378,684
Posted By Springbok Flyer

Hi guys, My build is finish and I am doing...

Hi guys,

My build is finish and I am doing final setup. SM suggest the following throws; ailerons 20mm up and down, elevators 60mm up and down, rudder 25mm both ways. Then they also suggest 30%...
Forum: RC Jets
07-01-2018, 02:03 AM
Replies: 1,970
Views: 378,684
Posted By Springbok Flyer

Ronnie, I have made my top tank half the...

Ronnie,

I have made my top tank half the length (as a total of 5 liters fuel for my AMT Pegasus HPe is more than enough) so it fit in front of the hatch under the fuse section. I have also now...
Forum: RC Jets
06-30-2018, 02:55 PM
Replies: 1,970
Views: 378,684
Posted By Springbok Flyer

Thx Ronnie, I was hoping to hear about some magic...

Thx Ronnie, I was hoping to hear about some magic options....LOL Your advice regarding the larger fender washers is great.

Cheers,

JanR
Forum: RC Jets
06-30-2018, 02:18 AM
Replies: 1,970
Views: 378,684
Posted By Springbok Flyer

Hi guys, How did you bolt the front section...

Hi guys,

How did you bolt the front section to the rear section with the tanks in position? I cannot reach the three bolts in the top half of the fuselage. If I take the tanks out and bolt the...
Forum: RC Jets
06-26-2018, 08:57 PM
Replies: 1,970
Views: 378,684
Posted By Springbok Flyer

Question Please explain, I am not sure h9wvto accomplish...

Please explain, I am not sure h9wvto accomplish that....

Thank you,

JanR
Forum: RC Jets
06-26-2018, 08:39 PM
Replies: 1,970
Views: 378,684
Posted By Springbok Flyer

Hi guys, Next question: where are you guys...

Hi guys,

Next question: where are you guys setting the neutral position for the flying stabs when using 220mm for the cg. Basically I am looking for a safe starting position. Once I have flown my...
Forum: RC Jets
06-11-2018, 06:30 PM
Replies: 1,970
Views: 378,684
Posted By Springbok Flyer

Cool, thanks Ronnie. Must say, I have always...

Cool, thanks Ronnie. Must say, I have always preferred the KISS principle with my models.

JanR
Forum: RC Jets
06-11-2018, 02:01 PM
Replies: 1,970
Views: 378,684
Posted By Springbok Flyer

Question Good advice, thanks. Are you guys flying...

Good advice, thanks.

Are you guys flying with or without leading edge slats? Mine don't have them. Also, are you using the conventional setup of ailerons and elevators or flaperons and elevons?...
Forum: RC Jets
06-10-2018, 05:56 PM
Replies: 1,970
Views: 378,684
Posted By Springbok Flyer

Ronnie, Fantastic, exactly what I wanted...

Ronnie,

Fantastic, exactly what I wanted know.

Cheers,

JanR
Forum: RC Jets
06-10-2018, 01:04 PM
Replies: 1,970
Views: 378,684
Posted By Springbok Flyer

Thank you guys, the cg advice is much...

Thank you guys, the cg advice is much appreciated.

A different question; do any of you shortern the two dorsal fins to improve ground clearance during take-off and landing? If so how do you...
Forum: RC Jets
06-10-2018, 02:47 AM
Replies: 1,970
Views: 378,684
Posted By Springbok Flyer

Hi guys, Can anyone confirm what cg they are...

Hi guys,

Can anyone confirm what cg they are using on a G2 version. The manual range is 200 to 220mm from where the wing leading edge meets the fuselage. Basically 200 is on the main removable...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.