RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: mjraines1
Showing results 1 to 13 of 13
Search took 0.08 seconds.
Forum: Glow Engines
03-09-2012, 04:52 PM
Replies: 54,816
Views: 5,392,321
Posted By mjraines1

RE: Welcome to Club SAITO !

On your on board glow. Do you leave it on at two clicks up when starting and leave it connected to the on board battery during flight?
Forum: Glow Engines
02-25-2012, 12:04 PM
Replies: 54,816
Views: 5,392,321
Posted By mjraines1

RE: Welcome to Club SAITO !

How about lock tight or thread lock?
Forum: Glow Engines
02-25-2012, 12:02 PM
Replies: 54,816
Views: 5,392,321
Posted By mjraines1

RE: Welcome to Club SAITO !

Hey what about kock tight or thread lock?
Forum: Glow Engines
02-24-2012, 03:24 PM
Replies: 54,816
Views: 5,392,321
Posted By mjraines1

RE: Welcome to Club SAITO !

You are correct. The 1/2 inch recess 3/8 inch deep is required for the adapter.

B & B is MIA?
Forum: Glow Engines
02-23-2012, 07:17 PM
Replies: 54,816
Views: 5,392,321
Posted By mjraines1

RE: Welcome to Club SAITO !

What is the part No. on the one you are using?
Forum: Glow Engines
02-23-2012, 07:15 PM
Replies: 54,816
Views: 5,392,321
Posted By mjraines1

RE: Welcome to Club SAITO !

Yes this is what I have? How about the one you pic on the left. Will it fit and does it have the lock nut? What's the part No. on it?
Forum: Glow Engines
02-23-2012, 06:52 PM
Replies: 54,816
Views: 5,392,321
Posted By mjraines1

RE: Welcome to Club SAITO !

Hobbsy,
Will the adapter on the left work on the short shaft using the lock nut adapter?
Forum: Glow Engines
02-23-2012, 06:51 PM
Replies: 54,816
Views: 5,392,321
Posted By mjraines1

RE: Welcome to Club SAITO !

If the one on the left will work on the short shat and still leave room for the lock nut, I think that may be the way to go?
Forum: Glow Engines
02-23-2012, 06:49 PM
Replies: 54,816
Views: 5,392,321
Posted By mjraines1

RE: Welcome to Club SAITO !

You are correct, you can see where the adapter comes thru the washer and leaves about 3/8 of an inch that must inset into the prop hub.
Forum: Glow Engines
02-23-2012, 06:47 PM
Replies: 54,816
Views: 5,392,321
Posted By mjraines1

RE: Welcome to Club SAITO !

I think you will find that on the short shaft adapter for the 1' shaft the adapter goes through the washer and then sets 3/8 of an inch into the prop hub. This has to be drilled to 1/2 inch dia. 3/8...
Forum: Glow Engines
02-23-2012, 06:35 PM
Replies: 54,816
Views: 5,392,321
Posted By mjraines1

RE: Welcome to Club SAITO !

Thanks, I'll try again tomorrow. I called several times today. He has what I need in the cat. I'll see if I can fax him a order tomorrow. So far I have been unsuccessful in getting intouch with...
Forum: Glow Engines
02-23-2012, 12:49 PM
Replies: 54,816
Views: 5,392,321
Posted By mjraines1

RE: Welcome to Club SAITO !

Thanks for the info. on B & B I have tried to contact them on several occasions. No one answers and the fax is not hook up. the .25 pilot and .50 bit is exactly what I need. Any thoughts on where...
Forum: Glow Engines
02-23-2012, 08:09 AM
Replies: 54,816
Views: 5,392,321
Posted By mjraines1

RE: Welcome to Club SAITO !

I have the 91 Satio with the short adapter from Tru Turn, The inset into the prop is 1/2 ' and 3/8' deep. This is on a prop 3/4' thick. (50%).
If you use a drill bit the shaffer beyond the bore is...
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.