RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: StZ
Showing results 1 to 13 of 13
Search took 0.03 seconds.
Forum: Glow Engines
11-30-2014, 09:35 AM
Replies: 54,816
Views: 5,394,302
Posted By StZ

What these photos/posts have to do with the Saito...

What these photos/posts have to do with the Saito engines?
Forum: Glow Engines
11-30-2014, 09:14 AM
Replies: 54,816
Views: 5,394,302
Posted By StZ

Thanks.

Thanks.
Forum: Glow Engines
11-29-2014, 06:30 AM
Replies: 54,816
Views: 5,394,302
Posted By StZ

Since I have access to a workshop, I will make...

Since I have access to a workshop, I will make the muffler (If I can find the dimensions) from aluminium using a lathe. It is very easy to produce.
As far as the brass is concerned, I do have a...
Forum: Glow Engines
11-28-2014, 11:47 AM
Replies: 54,816
Views: 5,394,302
Posted By StZ

It is a homemade muffler with thin walls. I...

It is a homemade muffler with thin walls. I cannot solder it elsewhere (I do not know how and I do not have, probably, the right equipment). The material seems to be copper! The previous guy said...
Forum: Glow Engines
11-28-2014, 10:20 AM
Replies: 54,816
Views: 5,394,302
Posted By StZ

You are absolutely right. The pressure tap is...

You are absolutely right. The pressure tap is looking down at the exhaust exit of the muffler at around 30 degrees off vertical (to the muffler)! I cannot use another muffler because I do not have...
Forum: Glow Engines
11-28-2014, 12:21 AM
Replies: 54,816
Views: 5,394,302
Posted By StZ

I will try to find out answers to your questions....

I will try to find out answers to your questions. The weather here is not very good at the moment (raining all the time). I will get back to you as soon as I can have the model outside and running....
Forum: Glow Engines
11-27-2014, 11:09 PM
Replies: 54,816
Views: 5,394,302
Posted By StZ

If there was a leak in the carb o-ring would it...

If there was a leak in the carb o-ring would it not run erratic during prolonged idle?
Forum: Glow Engines
11-27-2014, 11:07 PM
Replies: 54,816
Views: 5,394,302
Posted By StZ

Clunk is the correct length and not turned back...

Clunk is the correct length and not turned back on itself. Will check if there is a kink somewhere in the fuel lines.
Forum: Glow Engines
11-27-2014, 10:34 AM
Replies: 54,816
Views: 5,394,302
Posted By StZ

It should be that there is low back pressure to...

It should be that there is low back pressure to the tank from the muffler. When it dies rpm do not change. If it was leaning out, the rpms would increase somewhat, they do not!
The muffler nipple...
Forum: Glow Engines
11-27-2014, 06:58 AM
Replies: 54,816
Views: 5,394,302
Posted By StZ

The tubing is standard glow tube with o.d. of 5...

The tubing is standard glow tube with o.d. of 5 mm and i.d. of 2.5 mm.
Changing the h.s.n has no effect. The engine always stops when vertical. That is why my question concerns the exhaust. It...
Forum: Glow Engines
11-27-2014, 06:55 AM
Replies: 54,816
Views: 5,394,302
Posted By StZ

When the plane is vertical, no matter what we do...

When the plane is vertical, no matter what we do on the needle has an effect. It always stops when pointing upwards! Fuel lines and tank setup is OK.
Forgot to mention that engine stops within 2-4...
Forum: Glow Engines
11-27-2014, 06:26 AM
Replies: 54,816
Views: 5,394,302
Posted By StZ

I have the nut and pipe that goes into the head. ...

I have the nut and pipe that goes into the head. I also have something similar to an exhaust on the engine. Everything works fine. Endless idle and good transition. Problems start when the plane...
Forum: Glow Engines
11-26-2014, 12:38 PM
Replies: 54,816
Views: 5,394,302
Posted By StZ

Hi, I have bought a second hand FA65...

Hi,

I have bought a second hand FA65 without muffler. Can anyone give me the basic dimensions that are required to manufacture the muffler (length, outer diameter, inner diameters, etc)?
Any...
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.