RCU Forums - Search Results

Search: Posts Made By: fw190pilot

Showing results 1 to 10 of 10
Search took 0.08 seconds.

Forum: RC Jets

02-16-2009, 10:51 PM

Replies: 5,088

Bob Cat Copy Falcon 120 Jet

Views: 1,237,104

Posted By fw190pilot

RE: Bob Cat Copy Falcon 120 Jet

Baldeagle

To answer your question my flying (dry tanks full uat) cog is set at 13 1/2 inches back. Bare fuse with wingtube installed dry tanks, full uat, nose extended, and no canopy cog is...

Forum: RC Jets

02-15-2009, 09:57 PM

Replies: 5,088

Bob Cat Copy Falcon 120 Jet

Views: 1,237,104

Posted By fw190pilot

RE: Bob Cat Copy Falcon 120 Jet

Maidened my Falcon 120 today. Powered with a JetJoe 1400 just about the perfect amount of power for the airframe. Plenty of power for takeoff at 19.5 lbs wet but not so much to overstress the...

Forum: RC Jets

02-15-2009, 09:31 PM

Replies: 5,088

Bob Cat Copy Falcon 120 Jet

Views: 1,237,104

Posted By fw190pilot

RE: Bob Cat Copy Falcon 120 Jet

Whoops I screwed this up!:eek:

Forum: RC Jets

12-02-2008, 09:26 PM

Replies: 5,088

Bob Cat Copy Falcon 120 Jet

Views: 1,237,104

Posted By fw190pilot

RE: Bob Cat Copy Falcon 120 Jet

I used 125 ounce metal gear servos on all control surfaces. Putting a turbine on mine so put full size servos on all control surfaces.

Forum: RC Jets

08-20-2008, 09:24 PM

Replies: 5,088

Bob Cat Copy Falcon 120 Jet

Views: 1,237,104

Posted By fw190pilot

RE: Bob Cat Copy Falcon 120 Jet

Try ausjets Rob could most likely help you get one.

Forum: RC Jets

07-18-2008, 09:45 PM

Replies: 5,088

Bob Cat Copy Falcon 120 Jet

Views: 1,237,104

Posted By fw190pilot

RE: Bob Cat Copy Falcon 120 Jet

Some triangle stock and a little hysol isn't a bad idea to reinforce the mount plates. In particular the front plate. Not much holding that one in there.

Forum: RC Jets

07-11-2008, 10:08 PM

Replies: 5,088

Bob Cat Copy Falcon 120 Jet

Views: 1,237,104

Posted By fw190pilot

RE: Bob Cat Copy Falcon 120 Jet

A elcheapo 4 inch stove pipe (about 5 bucks) and a couple of 2 x 4 scraps will work fine. The stove pipe will withstand hot starts with no proplem. Trust me I have tested it. :D

Forum: RC Jets

06-10-2008, 11:35 PM

Replies: 5,088

Bob Cat Copy Falcon 120 Jet

Views: 1,237,104

Posted By fw190pilot

RE: Bob Cat Copy Falcon 120 Jet

Without the tube in the way 2 32oz and a 40oz dubro tanks will fit.

Forum: RC Jets

06-10-2008, 10:10 PM

Replies: 5,088

Bob Cat Copy Falcon 120 Jet

Views: 1,237,104

Posted By fw190pilot

RE: Bob Cat Copy Falcon 120 Jet

Hi guys just got a Falcon 120 and have a question about the front wing tube (the small one). Is it necesary for it to go through the fuse from wing to wing? Think it is too short to support any wing...

Forum: RC Jets

10-30-2007, 11:32 PM

Replies: 5,088

Bob Cat Copy Falcon 120 Jet

Views: 1,237,104

Posted By fw190pilot

RE: Bob Cat Copy Falcon 120 Jet

A piece of 4 inch elcheapo stove pipe works very well. Just have to make something to hold it at the right height. I would think that the flex hose wouldn't take any serious heat and or flame and...

Showing results 1 to 10 of 10