RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: Barfly
Showing results 1 to 16 of 16
Search took 0.15 seconds.
Forum: Glow Engines
05-08-2006, 12:09 PM
Replies: 46,892
Views: 2,632,869
Posted By Barfly

RE: Welcome to Club SAITO !

Iron Cross, I read your recent post about putting a 13 x 6 on the .56. I am flying the same engine and fuel, with 12 x 4 and 12 x 5, I thought the 13 x 6 would be too much, and it was! I put one on...
Forum: Glow Engines
04-05-2006, 10:47 AM
Replies: 46,892
Views: 2,632,869
Posted By Barfly

RE: Welcome to Club SAITO !

Ernie, solafein, from memory, Viton can go to 220*, which is 30-40* higher than the alternatives. Resists a wider range of chemicals, too. Should be good enough for our babies!

Bill, To follow...
Forum: Glow Engines
04-04-2006, 08:35 AM
Replies: 46,892
Views: 2,632,869
Posted By Barfly

RE: Welcome to Club SAITO !

Ernie,

I put this on a .56F, I also have a 1.00 but the carb throat is 8.5mm and the stack is only 8.0mm so no go. I believe the carb on the .82 is the same configuration as the .56 so the stack...
Forum: Glow Engines
04-03-2006, 11:15 AM
Replies: 46,892
Views: 2,632,869
Posted By Barfly

RE: Welcome to Club SAITO !

bldrums,

Viton is the material the 'O' ring is made with, it's a shiney black rubbery plastic. This is a normal 'O' ring designed for use in hydraulics etc., I bought it at a shop that...
Forum: Glow Engines
04-01-2006, 01:38 PM
Replies: 46,892
Views: 2,632,869
Posted By Barfly

RE: Welcome to Club SAITO !

More on stacks..... like we need it!

Anyhow, I just put a stack on my .56, fitted perfectly, holes and all. I used an 'O' ring to seal the gap, 8mm I.D. x 1.5mm thick, made of Viton. Makes a...
Forum: Glow Engines
03-05-2006, 02:13 PM
Replies: 46,892
Views: 2,632,869
Posted By Barfly

RE: Welcome to Club SAITO !

Bill,

This list will come from Hobby Shack in Singapore, my local Saito stockist. I don't believe they carry the Bru-Line filters. I figured I'd check some specialist filter suppliers around...
Forum: Glow Engines
03-05-2006, 12:13 PM
Replies: 46,892
Views: 2,632,869
Posted By Barfly

RE: Welcome to Club SAITO !

Well..... I guess we got this one wrapped up! Great info from all who responded to the 'stack' enquiry. Thanks guys. I've added two of these to my shopping list.

Cheers from the Barfly.
Forum: Glow Engines
03-04-2006, 12:47 PM
Replies: 46,892
Views: 2,632,869
Posted By Barfly

RE: Welcome to Club SAITO !

IronCross, are you still around here?

Looking back to your post #483 you mentioned that the stack for a .72 fits a .56. I can see they both have the same style carb but I cannot identify the...
Forum: Glow Engines
03-04-2006, 12:12 AM
Replies: 46,892
Views: 2,632,869
Posted By Barfly

RE: Welcome to Club SAITO !

Thanks Bill, and Jim,

I'll look into it (literally).

I'm sorry to be asking about stuff that you've been over before, but this has become a sizeable thread and I can't read it all in one...
Forum: Glow Engines
03-03-2006, 12:14 PM
Replies: 46,892
Views: 2,632,869
Posted By Barfly

RE: Welcome to Club SAITO !

Guys, How much crankshaft end float should there be? My 56F has ~.010". Only about 8 tanks through since I installed new stock bearings and crank, I thought it was tight, but not now.

Cheers...
Forum: Glow Engines
03-02-2006, 05:17 AM
Replies: 46,892
Views: 2,632,869
Posted By Barfly

RE: Welcome to Club SAITO !

Thanks evansh, I'm very familiar with Hobby Shack, been there many times. I'll shoot off an order as soon as get my ducks in a row. I'll be in Sg. in a couple weeks, maybe can pick up in person.

...
Forum: Glow Engines
03-02-2006, 05:11 AM
Replies: 46,892
Views: 2,632,869
Posted By Barfly

RE: Welcome to Club SAITO !

Shucks Bill, I feel silly for not seeing that. I think I need to change it on both my engines, the needle just falls through. Thanks for the pic.

Cheers from the Barfly.
Forum: Glow Engines
03-02-2006, 01:31 AM
Replies: 46,892
Views: 2,632,869
Posted By Barfly

RE: Welcome to Club SAITO !

Guys, how is the main needle sealed against fuel leakage? I can't see an 'O' ring in there, or anything else. Simply close tolerance, maybe?

Cheers from the Barfly.
Forum: Glow Engines
03-01-2006, 03:50 AM
Replies: 46,892
Views: 2,632,869
Posted By Barfly

RE: Welcome to Club SAITO !

Thanks Bill,

I'll check out that kit. I may have found my problem though, loose carb fuel inlet nipple and a tiny piece of crap inside the spray bar. I'll give it a new plug too, and see how it...
Forum: Glow Engines
03-01-2006, 02:08 AM
Replies: 46,892
Views: 2,632,869
Posted By Barfly

RE: Welcome to Club SAITO !

Thanks Jim,

The one I have is the only one I've ever seen. I bent the spray bay slightly, straightened it and now having trouble tuning it. Dunno if the spray bar is the cause, or something...
Forum: Glow Engines
02-28-2006, 01:02 PM
Replies: 46,892
Views: 2,632,869
Posted By Barfly

RE: Welcome to Club SAITO !

Guys,

Can anyone tell me what is the difference between a FA56 and a FA56F, the 'Fun Fly' version with the red anodized thrust washer.

Cheers from the Barfly.
Showing results 1 to 16 of 16


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.