RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: frankle951
Showing results 1 to 25 of 35
Search took 0.01 seconds.
Forum: RC Jets
06-10-2020, 08:58 PM
Replies: 57
Views: 4,490
Posted By frankle951

Sorry Steve, just reread your question, the nylon...

Sorry Steve, just reread your question, the nylon gear has to be slotted on the aluminum arm to move, for steering....
Forum: RC Jets
06-10-2020, 12:56 PM
Replies: 57
Views: 4,490
Posted By frankle951

Here are some pics, if not enough, I will pull...

Here are some pics, if not enough, I will pull the gear out.
https://cimg3.ibsrv.net/gimg/www.rcuniverse.com-vbulletin/2000x1504/20200610_165432_5ce06b425e54278b9a2e11b33f1853cab988c357.jpg...
Forum: RC Jets
06-09-2020, 05:56 AM
Replies: 57
Views: 4,490
Posted By frankle951

Going to remove the front gear to get photo.

Going to remove the front gear to get photo.
Forum: RC Jets
06-06-2020, 05:47 AM
Replies: 57
Views: 4,490
Posted By frankle951

Sorry Steve, still working on the photo.

Sorry Steve, still working on the photo.
Forum: RC Jets
06-06-2020, 02:48 AM
Replies: 57
Views: 4,490
Posted By frankle951

About $900.00 shipped, from feibao, take about 3...

About $900.00 shipped, from feibao, take about 3 weeks.
Forum: RC Jets
06-03-2020, 05:05 AM
Replies: 57
Views: 4,490
Posted By frankle951

I will look and take pictures.

I will look and take pictures.
Forum: RC Jets
05-19-2020, 02:25 PM
Replies: 57
Views: 4,490
Posted By frankle951

Well, maybe not, might just use a better servo...

Well, maybe not, might just use a better servo arm, the one I made was not accurate, my friend has a 3D cutter, and he made a Prototype of what I need, a lot more better made, going to use a 20mm...
Forum: RC Jets
05-18-2020, 12:40 PM
Replies: 57
Views: 4,490
Posted By frankle951

Yes, I'm going to use the leading edge, thanks...

Yes, I'm going to use the leading edge, thanks for the pics.
Forum: RC Jets
05-09-2020, 06:36 PM
Replies: 57
Views: 4,490
Posted By frankle951

Yes, me and my friend larry, flip the f-16 over...

Yes, me and my friend larry, flip the f-16 over on a stand and start playing with the locking bar, moving it forward and back, it really lock in place when moving the gear forward, and moving the...
Forum: RC Jets
05-09-2020, 01:49 PM
Replies: 57
Views: 4,490
Posted By frankle951

Well got a lot done, was able to start up the...

Well got a lot done, was able to start up the Jetcat P160se and taxi around, no leaks, all three tank drain perfect, figure out the locking bars on the main retract, well back to work.
Forum: RC Jets
05-05-2020, 02:33 PM
Replies: 57
Views: 4,490
Posted By frankle951

Sorry, I love the tiger meet, every time I go to...

Sorry, I love the tiger meet, every time I go to a jet meet, you see the same old military scheme, I'm not much on military color.
Forum: RC Jets
05-04-2020, 02:10 PM
Replies: 57
Views: 4,490
Posted By frankle951

Ok, guys the main retracts are not locking in...

Ok, guys the main retracts are not locking in place, to the gear solid ?, I see other manufacturers use a air cylinder to lock there ?, I sent Catherine at feibao a email asking how the bar Supposed...
Forum: RC Jets
04-30-2020, 05:49 AM
Replies: 57
Views: 4,490
Posted By frankle951

Time to cleanup the front board, I remove the...

Time to cleanup the front board, I remove the regulator, to make room for the uat tank, and forgot, the steering servo is 6volt, well I smell smoke, going to remove the nose gear to replace the...
Forum: RC Jets
04-26-2020, 10:11 AM
Replies: 57
Views: 4,490
Posted By frankle951

Wow, getting there, all wires, fuel lines, cable...

Wow, getting there, all wires, fuel lines, cable ran, need to run retract air lines from the mains, to the front, then I can set the three tanks in the fuselage, learn the throttle to the ecu, spool...
Forum: RC Jets
04-23-2020, 12:34 PM
Replies: 57
Views: 4,490
Posted By frankle951

Ok, air tanks installed. ...

Ok, air tanks installed.
https://cimg9.ibsrv.net/gimg/www.rcuniverse.com-vbulletin/2000x1504/20200423_150629_9702f2a888a496296822a2fbc46d5cbcb8945d0d.jpg
Forum: RC Jets
04-23-2020, 12:32 PM
Replies: 57
Views: 4,490
Posted By frankle951

Ok, I have been looking at ppg paint color, I...

Ok, I have been looking at ppg paint color, I think I like the tiger meet scheme, not really sure yet....
Forum: RC Jets
04-23-2020, 09:54 AM
Replies: 57
Views: 4,490
Posted By frankle951

Well, it's raining outside, maybe I can get more...

Well, it's raining outside, maybe I can get more done today, just received my two large Robert's air tanks, I can install them in the fuselage today and run the lines, I have one brake line to run,...
Forum: RC Jets
04-22-2020, 05:12 PM
Replies: 57
Views: 4,490
Posted By frankle951

Ok bob, it went over my head, but it's almost...

Ok bob, it went over my head, but it's almost ready to taxi around.
Forum: RC Jets
04-22-2020, 09:40 AM
Replies: 57
Views: 4,490
Posted By frankle951

Sorry bob, don't understand NG ??

Sorry bob, don't understand NG ??
Forum: RC Jets
04-21-2020, 11:56 AM
Replies: 57
Views: 4,490
Posted By frankle951

Well, all servo wire ran, just bolted the turbine...

Well, all servo wire ran, just bolted the turbine in, looking at the wires, box, ic board, would love to put everything up front for weight, but the cable are to short, I hate to add weight up front....
Forum: RC Jets
04-16-2020, 03:47 PM
Replies: 57
Views: 4,490
Posted By frankle951

I think my biggest challenge is going to be the...

I think my biggest challenge is going to be the gear doors, I may use a Linear servo, but to make it easy, air cylinder.
Forum: RC Jets
04-16-2020, 03:41 PM
Replies: 57
Views: 4,490
Posted By frankle951

Ok, got a lot more done, on the F-16, finish up...

Ok, got a lot more done, on the F-16, finish up the back half section, that hold 5 servo, two elevators, two ailerons and one rudder, the rudder was the hardest to finish, with the servo inside the...
Forum: RC Jets
04-11-2020, 06:42 AM
Replies: 57
Views: 4,490
Posted By frankle951

Well, got a little done on the retract, the mains...

Well, got a little done on the retract, the mains are bolted in, took a lot of dremel work, but there not hitting the side, now I'm cutting the slots for nose gear, here some pics....
Forum: RC Jets
04-11-2020, 03:07 AM
Replies: 57
Views: 4,490
Posted By frankle951

Wow, it's the same gear, thanks for the pictures,...

Wow, it's the same gear, thanks for the pictures, your pics help me with the gear doors hinge location.
Forum: RC Jets
04-09-2020, 05:08 AM
Replies: 57
Views: 4,490
Posted By frankle951

Do you have the retracts yet ?, any pictures you...

Do you have the retracts yet ?, any pictures you can share ?
Showing results 1 to 25 of 35
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.