RCU Forums
0 2020/08/16 11:59:50
0 2020/08/16 12:13:25
0 2020/08/16 12:13:32
0 2020/08/16 12:13:38
0 2020/08/16 12:18:03
0 2020/08/16 12:22:04
Beings my side planking did not completely conceal the corners of all the fuse formers, I also found it desirable to lightly sand the outer corners, beveling them slightly, in order to ensure the sheet would lie flat across all surfaces, upon gluing.
Beings my side planking did not completely conceal the corners of all the fuse formers, I also found it desirable to lightly sand the outer corners, beveling them slightly, in order to ensure the sheet would lie flat across all surfaces, upon gluing.
0 2020/08/16 12:22:16
0 2020/08/16 16:08:17
0 2020/08/16 16:08:21
0 2020/08/16 16:08:24
0 2020/08/16 16:08:28
Note I am trimming at a bevel.
Note I am trimming at a bevel.
0 2020/08/16 16:54:13
0 2020/08/16 16:54:25
I trimmed the sheeting "close," with an Exacto knife. But will finish with a razor plane and sanding block.
I trimmed the sheeting "close," with an Exacto knife. But will finish with a razor plane and sanding block.
0 2020/08/16 16:54:30
Shots of me razor-planing the bottom sheeting.
Shots of me razor-planing the bottom sheeting.
0 2020/09/03 22:08:04
Shots of me razor-planing the bottom sheeting.
Shots of me razor-planing the bottom sheeting.
0 2020/09/03 22:08:26
0 2020/09/03 22:12:20
0 2020/09/03 22:12:23
0 2020/09/03 22:25:05
0 2020/09/03 22:25:31
0 2020/09/03 22:38:50
0 2020/09/03 22:38:59
0 2020/09/03 22:39:08
View from outside of my cowl.
View from outside of my cowl.
0 2020/09/03 22:42:53
View from inside of Tim's cowl.
View from inside of Tim's cowl.
0 2020/09/03 22:42:59
Here, I am cutting-out the valve cover clearance hole.
Here, I am cutting-out the valve cover clearance hole.
0 2020/09/03 22:44:25
Initial trial fit after original opening was cut.
Initial trial fit after original opening was cut.
0 2020/09/03 22:49:11
In this and the next picture, I am tracing where I desire to remove more material for curved and symmetrical amounts of clearance around the valve cover; as well as to round corners.
In this and the next picture, I am tracing where I desire to remove more material for curved and symmetrical amounts of clearance around the valve cover; as well as to round corners.
0 2020/09/03 22:49:31
0 2020/09/03 22:49:41
Sanding to my retraced lines and curves.
Sanding to my retraced lines and curves.
0 2020/09/03 22:49:51
Second trial fit.
Second trial fit.
0 2020/09/03 22:49:56
0 2020/09/03 22:50:16
0 2020/09/03 23:01:30
0 2020/09/03 23:01:32
0 2020/09/03 23:01:37
0 2020/09/03 23:08:28
0 2020/09/03 23:08:31
0 2020/09/03 23:08:37
Tim begins by tracing the front of the opening on the inside of the cowl.
Tim begins by tracing the front of the opening on the inside of the cowl.
0 2020/09/03 23:13:47
And, finishes on the outside of the cowl.
And, finishes on the outside of the cowl.
0 2020/09/03 23:13:55
Advertising | Cookie Policy | Privacy Statement | Terms of Service | Manage Preferences Your Privacy Choices
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.