RCU Forums
0 2021/03/05 16:39:26
0 2021/03/05 16:39:30
0 2021/03/05 16:39:35
Nice color, numbered placement guide for the digital decals.
Nice color, numbered placement guide for the digital decals.
0 2021/03/06 14:53:28
Large general decals
Large general decals
0 2021/03/06 14:53:32
All of the digital decals included.
All of the digital decals included.
0 2021/03/06 14:53:39
Close up of the electronics. They look similar to a Taigan MFU. Shows the ability to hook up a hobby grade transmitter, but uses what looks to be a Molex connection for that and not a standard servo type cable.
Close up of the electronics. They look similar to a Taigan MFU. Shows the ability to hook up a hobby grade transmitter, but uses what looks to be a Molex connection for that and not a standard servo type cable.
0 2021/03/06 14:53:44
Bottom of the chassis with the nylon tracks
Bottom of the chassis with the nylon tracks
0 2021/03/06 14:53:50
Lower hull.
Lower hull.
0 2021/03/06 14:53:55
Wheels came with bronze bushings (5x8x2.5mm). Can be adapted to take 5x9x3mm bearings easily.
Wheels came with bronze bushings (5x8x2.5mm). Can be adapted to take 5x9x3mm bearings easily.
0 2021/03/06 14:54:00
Part of the smoke system. I produces tons of smoke. This motor is wired to one of the drive motors. I assume that is so the volume of smoke will increase as the motor speed increases.
Part of the smoke system. I produces tons of smoke. This motor is wired to one of the drive motors. I assume that is so the volume of smoke will increase as the motor speed increases.
0 2021/03/06 14:54:07
Similar torsion spring setup to some HL tanks, but the spring bale is larger diameter.
Similar torsion spring setup to some HL tanks, but the spring bale is larger diameter.
0 2021/03/06 14:54:13
Bottom of the turret. Greased from the factory
Bottom of the turret. Greased from the factory
0 2021/03/06 14:54:19
Turret setup. Uses servo recoil and motor driven elevation.
Turret setup. Uses servo recoil and motor driven elevation.
0 2021/03/06 14:54:24
Turret ring has ball bearings installed.
Turret ring has ball bearings installed.
0 2021/03/06 14:54:29
Turret rotation motor.
Turret rotation motor.
0 2021/03/06 14:54:37
Inside of turret upper.
Inside of turret upper.
0 2021/03/06 14:54:42
Turret detail with mount for IR system. IR system is similar to Taigen.
Turret detail with mount for IR system. IR system is similar to Taigen.
0 2021/03/06 14:54:47
Upper hull underside.
Upper hull underside.
0 2021/03/06 14:54:53
Upper hull detail.
Upper hull detail.
0 2021/03/06 14:55:00
0 2021/03/07 23:19:47
0 2021/03/07 23:19:51
0 2021/03/07 23:19:56
0 2021/03/07 23:20:00
0 2021/04/10 15:19:28
0 2021/04/10 15:20:36
Replaced the Hooben wheels with the left over Heng Long ZTZ-99 wheels I had laying around after replacing them on my HL ZTZ-99 with metal ones. I am not going to use metal wheels on this as the suspension arms are plastic and I don't know of any metal ones from Hooben. The Hooben wheels had brass bushings, but I have installed bearings in the HL wheels.
Replaced the Hooben wheels with the left over Heng Long ZTZ-99 wheels I had laying around after replacing them on my HL ZTZ-99 with metal ones. I am not going to use metal wheels on this as the suspension arms are plastic and I don't know of any metal ones from Hooben. The Hooben wheels had brass bushings, but I have installed bearings in the HL wheels.
0 2021/04/10 15:46:03
Shown with Tamiya apple installed.
Shown with Tamiya apple installed.
0 2021/04/10 15:46:10
Clark mount from the top.
Clark mount from the top.
0 2021/04/10 15:46:17
I can close the door and hide the mount when I'm not using an apple.
I can close the door and hide the mount when I'm not using an apple.
0 2021/04/10 15:46:25
Got magnets installed to hold the turret together for maintenance.
Got magnets installed to hold the turret together for maintenance.
0 2021/04/10 15:46:31
Upper magnets shown and replaced the Hooben apple mount with a Clark mount to accept the Tamiya apple.
Upper magnets shown and replaced the Hooben apple mount with a Clark mount to accept the Tamiya apple.
0 2021/04/10 15:46:36
Installed a Henntec for a T-72/T-90 that will be mated to some HL metal T-72 idlers. I have some, but the bearing is 5mm and the Henntec shafts are 4mm. I have ordered some 4mm bearings that fit the idlers. Also I poured resin in the bottom of the hull which really stiffened it up. I learned from my first time doing this to seal up every hole with hot glue before pouring the resin. Didn't lose a single drop this time.
Installed a Henntec for a T-72/T-90 that will be mated to some HL metal T-72 idlers. I have some, but the bearing is 5mm and the Henntec shafts are 4mm. I have ordered some 4mm bearings that fit the idlers. Also I poured resin in the bottom of the hull which really stiffened it up. I learned from my first time doing this to seal up every hole with hot glue before pouring the resin. Didn't lose a single drop this time.
0 2021/04/10 15:46:45
Shows connect the smaller motor to the M2 connector and the larger drive motor to the M1 slot.
Shows connect the smaller motor to the M2 connector and the larger drive motor to the M1 slot.
0 2021/04/13 22:36:53
0 2021/04/18 17:25:53
0 2021/04/18 17:25:57
0 2021/04/18 17:25:59
0 2021/04/18 17:26:01
0 2021/04/18 17:26:03
0 2021/04/18 17:26:05
Advertising | Cookie Policy | Privacy Statement | Terms of Service | Manage Preferences Your Privacy Choices
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.