RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: HarryC
Showing results 1 to 13 of 13
Search took 0.01 seconds.
Forum: RC Jets
12-16-2019, 09:22 AM
Replies: 225
Views: 52,362
Posted By HarryC

I have just come back from a fine winter flying...

I have just come back from a fine winter flying session and at last feel that I can give the Assist a wholehearted endorsement.
I set aside the time to dismantle and re-assemble my Hawker Demon so...
Forum: RC Jets
12-03-2019, 07:19 AM
Replies: 225
Views: 52,362
Posted By HarryC

Well done Gary, that was the issue. Now what is...

Well done Gary, that was the issue. Now what is puzzling me is that after the last Assist update I did see the "damping only" box, which means I had at that time got the relevant .bin file. Anyway,...
Forum: RC Jets
12-03-2019, 04:00 AM
Replies: 225
Views: 52,362
Posted By HarryC

Wayne, my main issue with Assist is, or was, its...

Wayne, my main issue with Assist is, or was, its determination to be a flight controller instead of the traditional damper. It has spoiled the handling of a small biplane by making it far too lively....
Forum: RC Jets
12-02-2019, 12:15 AM
Replies: 225
Views: 52,362
Posted By HarryC

There are similar comments on the German language...

There are similar comments on the German language Jetiforum site. Whoever advised Jeti on what the Assist should do is to blame, because Assist is not a gyro, it is a flight controller. It does not...
Forum: RC Jets
12-01-2019, 09:47 AM
Replies: 225
Views: 52,362
Posted By HarryC

Hi Wayne, I use a similar ish method but keep...

Hi Wayne,
I use a similar ish method but keep my values in the Tx, constantly transmitted using a spare channel - with 16/24 channels available it isn't usually a problem! My reason is that I don't...
Forum: RC Jets
12-01-2019, 01:00 AM
Replies: 225
Views: 52,362
Posted By HarryC

Hi Wayne, that works a bit better, I had...

Hi Wayne, that works a bit better, I had misunderstood your terms and swopped the function and tuning numbers. However, some problems remain.

Strictly speaking you don't need the divisor of 100 in...
Forum: RC Jets
11-30-2019, 02:04 PM
Replies: 225
Views: 52,362
Posted By HarryC

Wayne, that's a good point about why not to use...

Wayne, that's a good point about why not to use the flap servo channel as the gain mode control, though if I was doing that I would normally create a gain function assigned to the flap switch and...
Forum: RC Jets
11-30-2019, 04:49 AM
Replies: 225
Views: 52,362
Posted By HarryC

Gary, For the gyro ON/OFF switch, go into...

Gary,
For the gyro ON/OFF switch, go into configuration, channel assignment, assign additional channels. There is an item called "assist off", this allows you to set a 2 position switch as a master...
Forum: RC Jets
02-28-2018, 03:45 AM
Replies: 225
Views: 52,362
Posted By HarryC

yes but its a problem of how it handles trims,...

yes but its a problem of how it handles trims, not a problem of how it handles crow.
Forum: RC Jets
02-28-2018, 03:39 AM
Replies: 225
Views: 52,362
Posted By HarryC

That's nothing to do with crow. That is a trim...

That's nothing to do with crow. That is a trim problem and will occur with any change of trim value such as flight mode trim, mix flap to elevator trim etc.

I do experience the problem of neutral...
Forum: RC Jets
02-28-2018, 02:35 AM
Replies: 225
Views: 52,362
Posted By HarryC

Hold on! My Assist works properly with crow...

Hold on! My Assist works properly with crow braking!! I have aileron 1 and aileron 2. Stick priority is 125% because I like gyro gain to zero as soon as possible when I move the sticks. Confirmed...
Forum: RC Jets
02-28-2018, 02:23 AM
Replies: 225
Views: 52,362
Posted By HarryC

Then just set all 3 modes to dampening mode. I...

Then just set all 3 modes to dampening mode. I would not, you should always have an OFF mode in case of problems, gyro breaks loose etc.
Forum: RC Jets
02-28-2018, 12:00 AM
Replies: 225
Views: 52,362
Posted By HarryC

Digitech - my Demon sees trim like the Assist...

Digitech - my Demon sees trim like the Assist does and the Demon reduces the gain due to stick priority. It's the same for iGyro, ACT Fuzzy Pro, Eagle Tree Guardian, Aura 8 etc etc. Any gyro sees...
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.